Temporary measurements to collect reliable measurement data.

Measurement campaigns

Measurement campaigns in the sewage system. For the temporary collection of measurement data, we offer more than 30 measuring devices of different nominal sizes and measurement methods for rent. The measuring devices are each equipped with data transmission technology so that the measurement data can be conveniently viewed and streamed online on the ARAbella cloud management system.

Non-intrusive measurement of flow rate and temperature

Autarkic clamp-on flow measurement

Autarkic clamp-on flow measurement Low installation costs When setting up new flow measuring points in a drinking water supply network, it is often not the measuring instrument that is the main cost factor, but rather the installation effort (supply interruption, pipe work, power supply, flushing of the pipe, etc.). The installation of the autarkic Clamp-on flow meter does not require any intervention in the pipeline and can also simply be installed underground if a shaft construction is not economical.

LDM partially filled waste water flow measurement

Ultrasonic transit time difference flow measurement for wastewater, raw wastewater and rainwater

LDM partially filled Flow measurement

Highly precise flow value acquisition. The LDM is a calibrated measuring device for backflow-free flow measurement of waste water in open channels or free flowing lines. 10 flow velocity measuring sections distributed over the entire cross section provide most accurate flow values when the sensor is partially or fully filled. The level measurement is integrated in the device housing.

Low-power flow regulator with partly filled flow measurement

LDMdrive

The first 100% self-sufficient discharge controller with precise flow measurement and continuous monitoring on the process control system

Portable flow measurement for wastewater and external water

Temporary use of the proven MID for full filling to collect high-precision measurement data.

Portable flow measurement with MID

Waste water and external water flow measurement Measurements are performed with a high-precision, portable MID flowmeter mechanically protected by a plastic layer, which is normally installed in existing shafts and ducts without structural modifications. A bypass cushion completely seals the channel cross section and guides the entire water quantity completely through the measuring system.

Special solutions for measuring wastewater, raw wastewater and rainwater under the most difficult conditions.

Stationary flow measurement for wastewater

When the impossible becomes possible. High flow velocities, steep gradients, tight spaces, large measuring range. The more difficult the measuring task, the more suitable is the stationary flow measurement, which can often be retrofitted in existing structures and shafts.

TF stationäre Durchflussmessung teilgefüllt für Abwasser und Regenwasser

Ultrasonic transit time difference measurement with dry weather gutter

TF Stationary flow measurement partially filled

The TF Stationary Flow Measurement is a calibrated measuring channel for backflow-free flow measurement of wastewater, raw wastewater and rainwater in open channels or open channels.

Installation in waste water structures, underground facilities, explosive environments

Proud of our craft!

Assemblies

Day after day, STEBATEC fitters honour our craft by carrying out installations of the highest quality that are a joy to the eye of the professional.

Non-intrusive ultrasonic flow measurement for closed and fully filled pipelines.

Clamp-on flow measurement

Flow measurement on the outer wall of the pipe. With a flowmeter with clamp-on transducers it is possible to measure the flow in pipes simply from the outside. The transducers are installed on the pipeline with little technical effort and without process interruption. Rotationally symmetric flow profiles can be measured with only one acoustic section; non-symmetric ones require the use of several sections.

Stationary flow measurement for calibration in the calibration facility

Proven certainty and security for projects and customers.

Hydraulic laboratory and calibration plant

In preparation for projects with hydraulic complexity, we offer not only the experimental model approach in the hydraulics laboratory but also investigations and verifications by means of flow simulations. Our experts are at your disposal for further information.

Simple flow measurement without loss of cross section.

Portable sewer mouse

Waste water flow measurement. Using the portable pulse Doppler sensor with battery supply, the sewer mouse scans the velocity profile in several cells and calculates the flow together with the measured water level.

Solutions from site evaluation and maintenance concept to project planning and installation.

Water Flow Measurement Ultrasonic transit time

Precise determination of the flow rate The range of application of water flow measurement extends from small watercourses to large rivers with water containing large amounts of suspended matter. For this purpose, ultrasonic impulse packages are sent through the water. Based on their characteristic features, the transit time of the signals is determined on the receiving side.

Thema: Flow measurement

Measurement campaigns

Autarkic clamp-on flow measurement

LDM partially filled Flow measurement

LDMdrive

Portable flow measurement with MID

Stationary flow measurement for wastewater

TF Stationary flow measurement partially filled

Assemblies

Clamp-on flow measurement

Hydraulic laboratory and calibration plant

Portable sewer mouse

Water Flow Measurement Ultrasonic transit time

Follow us …

Offers, solutions and services

Topics

Search

Industries

Field of application